Ifm Flow Switch Manual / Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 :

Out1 switches when the volumetric flow quantity set with imps has been reached. • do not mount in downpipes that are open at the bottom! The sensor tip must not be in contact with the pipe wall. 9 2 5 configure the analogue output for volumetric flow. • do not mount in downpipes that are open at the bottom!

The sensor tip must not be in contact with the pipe wall. Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 — Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 from

8 additional settings (optional) 8. 4.2 interference in the pipe . The preset counter is only reset. (for media other than water → 8.1: • do not mount in downpipes that are open at the bottom! > all leds light and go out again step by step during this time the . The sensor tip must be . ▻ switch on the supply voltage.

▻ switch on the supply voltage.

(for media other than water → 8.1: The values are valid for water and installation in pipes 2". The preset counter is only reset. 3.2 sources of interference in . 9 2 5 configure the analogue output for volumetric flow. 8 1 change the switch point 8. 10 3 4 manual counter reset. ▻ switch on the supply voltage. The sensor tip must not be in contact with the pipe wall. Out1 switches when the volumetric flow quantity set with imps has been reached. The sensor tip must be . They change with other media/other pipe diameters. If the operating instructions or the technical data are not adhered to, personal.

• do not mount in downpipes that are open at the bottom! If the operating instructions or the technical data are not adhered to, personal. The unit detects the flow speed to the calorimetric measuring principle and switches the outputs s1 and s2: • do not mount in downpipes that are open at the bottom! 8 1 change the switch point 8.

3.2 sources of interference in . Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 — Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 from

8 additional settings (optional) 8. The sensor tip must not be in contact with the pipe wall. 8 1 change the switch point 8. The values are valid for water and installation in pipes 2". • do not mount in downpipes that are open at the bottom! ▻ switch on the supply voltage. (for media other than water → 8.1: • do not mount in downpipes that are open at the bottom!

7 3 error during adjustment 8.

• do not mount in downpipes that are open at the bottom! 4.2 interference in the pipe . 9 2 5 configure the analogue output for volumetric flow. If the operating instructions or the technical data are not adhered to, personal. The sensor tip must not be in contact with the pipe wall. They change with other media/other pipe diameters. The values are valid for water and installation in pipes 2". 7 3 error during adjustment 8. The unit detects the flow speed to the calorimetric measuring principle and switches the outputs s1 and s2: > all leds light and go out again step by step during this time the . 10 3 4 manual counter reset. Out1 switches when the volumetric flow quantity set with imps has been reached. 3.2 sources of interference in .

If the operating instructions or the technical data are not adhered to, personal. The sensor tip must not be in contact with the pipe wall. 9 2 5 configure the analogue output for volumetric flow. • do not mount in downpipes that are open at the bottom! The meter saves the totalled volumetric flow quantity every 10 minutes.

(for media other than water → 8.1: Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 — Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 from

If the operating instructions or the technical data are not adhered to, personal. They change with other media/other pipe diameters. 7 3 error during adjustment 8. The sensor tip must not be in contact with the pipe wall. Out1 switches when the volumetric flow quantity set with imps has been reached. The meter saves the totalled volumetric flow quantity every 10 minutes. The sensor tip must not be in contact with the pipe wall. 4.2 interference in the pipe .

The sensor tip must be .

The unit detects the flow speed to the calorimetric measuring principle and switches the outputs s1 and s2: The sensor tip must not be in contact with the pipe wall. • do not mount in downpipes that are open at the bottom! 8 additional settings (optional) 8. 9 2 5 configure the analogue output for volumetric flow. 8 1 change the switch point 8. 10 3 4 manual counter reset. The preset counter is only reset. (for media other than water → 8.1: They change with other media/other pipe diameters. 7 3 error during adjustment 8. • do not mount in downpipes that are open at the bottom! The values are valid for water and installation in pipes 2".

Ifm Flow Switch Manual / Aclk Sa L Ai Dchcsewivucohlod0ahxthdukhrqgbumyababggj3cw Sig Aod64 2fmcshqxrt7jo9d7tw55ada9yqiq Adurl Ctype 5 :. (for media other than water → 8.1: The sensor tip must not be in contact with the pipe wall. 7 3 error during adjustment 8. 8 additional settings (optional) 8. • do not mount in downpipes that are open at the bottom!